Fisher Price V0099 Instruction Manual with Setup Tips
Fisher Price V0099 Instruction Manual with Setup Tips
Blog Article
Fisher-Price V0099 Snugabunny Cradle Swing: A Comprehensive Guide
The Fisher-Price V0099 Snugabunny Cradle Swing is a versatile and soothing device designed to comfort infants with its gentle rocking motions and cozy environment. This guide provides detailed information on setting up, operating, maintaining, and storing the swing to ensure safety and longevity. Fisher price v0099 manual
????️ Assembly Instructions
Tools Required:
- Phillips screwdriver (not included)
- Allen wrench (included)(manuals.plus)
Assembly Steps:
- Attach the Mobile Dome:
- Fit the tabs on the mobile dome into the slots on the motorized frame.
- Press near each tab to “snap” the dome into place.(manuals.plus)
- Install the Lower Legs:
- Fit a foot onto the end of each lower leg.
- Insert two #8 x ½” screws through the bottom of each foot and into the lower leg. Tighten fully with a Phillips screwdriver.(manuals.plus)
- Attach Upper Legs:
- Fit an upper leg onto a lower leg. The upper legs are designed to fit the lower legs one way; if it doesn't seem to fit, try the other upper leg.
- Insert an M5 x 35 mm bolt through the opening in the upper leg tube. Tighten fully with the Allen wrench.
- Repeat this procedure for the other upper leg.(manuals.plus)
- Secure the Frame Support Bar:
- Fit the power cord into the retainer on a lower leg.
- While pressing the button on a leg assembly, fit it into a tube on the motorized frame. Ensure the button on the leg “snaps” into the hole in the tube.
- Repeat this for the other leg assembly.
- Pull apart the legs.
- Lift the free end of the frame support bar.
- Fit the hole in the frame support bar over the peg on the opposite leg. Push to “snap” the frame support bar in place.(manuals.plus)
- Connect the Power Cord:
- Plug the power cord from the motorized frame assembly into the power cord in the frame assembly.(manuals.plus)
- Assemble the Seat:
- Fit the side rails to the side tabs on the seat.
- Insert four #8 x 1” screws into the side rails. Tighten fully with a Phillips screwdriver.
- Fit the lower seat tube into the short tube on the seat back.
- Fit the lower seat tube onto the upper seat tube.
- Insert an M5 x 35 mm bolt into the short tube. Tighten fully with the Allen wrench.
- Insert an M5 x 35 mm bolt into the upper seat tube. Tighten fully with the Allen wrench.(manualslib.com, manuals.plus)
- Install the Restraint System:
- Insert the waist belts through the lowest slots in the pad. Ensure the waist belts are not twisted.
- Fold the top of the pad down.
- Insert the shoulder belts through the upper slots in the seat pad back.
- Insert the ends of the shoulder belts through the lower slots in the seat pad back.
- Fit the pad edges around the rim of the seat.
- Insert the restraint pad through the lower slot and the waist restraints through the upper slots in the body support.
- Fit the link on the bunny toy to the restraint pad.
- Hook both elastic loops at the top of the seat pad around the pegs at the top of the seat.
- Hook both elastic loops at the bottom of the seat pad around the pegs at the bottom of the seat.
- Fit the ends of the canopy stay into the pocket on each side of the seat pad.
- Insert the strings on each mobile toy into the slot in each mobile hanger.
- Pull each toy down to ensure it is secure.
- Lift the top of the canopy and fit it into the clip on the swing tube.(manuals.plus)
???? Power Options
The Snugabunny Cradle Swing can be powered in two ways:
- AC Adapter:
- Plug the AC adapter into the power cord extending from the back of a leg.
- Plug the AC adapter into a standard wall outlet.
- Use the AC adapter only in a wall outlet. Do not plug the adapter into a ceiling outlet.(manuals.plus)
- Battery Operation:
- Loosen the screws in the battery compartment door with a Phillips screwdriver and remove the door.
- Insert four “D” (LR20) alkaline batteries into the battery compartment.
- Replace the battery compartment door and tighten the screws.
- Note: Low battery power may cause product movement to slow, sound and lights to become faint, or the product to turn off. If this happens, use the AC adapter as a power source or replace the batteries.(manuals.plus)
???? Operating the Swing
- Swing Speed:
- Press the swing speed buttons to select any of the six-speed settings.
- As with most battery-powered swings, a heavier child will reduce the amount of swinging motion on all settings. In most cases, the low setting works best for a smaller child, while the high setting works best for a larger child.(manuals.plus)
- Music and Sounds:
- Press the music/sound selection buttons to choose from various music and sound options.
- Press the same button again to turn the sound off.
- Press the same button again to turn the sound on again.
- The mobile, music, or sounds will turn off after approximately 20 minutes. Press the mobile, music, or sounds button to restart. When you restart the music, a different song will play.(manuals.plus)
- Volume Control:
- Press the volume buttons to adjust the volume level.(manuals.plus)
???? Care and Maintenance
- Cleaning the Seat Pad:
- Unbuckle the restraint system.
- Remove the top of the canopy from the clip on the swing tube.
- Pull the ends of the canopy stay out of the pockets on the pad.
- Slide the canopy stay out of the canopy sleeve.
- Remove the pad elastic loops from the pegs and unfasten the pad fasteners from the seat.
- Remove the pad from the restraint system.
- Machine wash the pad in cold water with mild detergent. Do not use bleach. Tumble dry on low heat and remove promptly.(manuals.plus)
- Cleaning the Frame and Other Components:
- To clean the seat, restraint system, tray, mobile, and motorized frame, use a mild cleaning agent and a damp cloth. Rinse with clean water to remove residue.(manuals.plus)
- Reassembling the Seat Pad:
- Replace the pad on the seat.
- Periodically check the swing for loose fasteners or broken parts and tighten as needed.(manuals.plus)
???? Storage Instructions
- Preparing for Storage:
- Push the tab on the frame support bar to release it.
- Lean the swing frame against a wall for storage.
- Remove the batteries for long-term storage.(manuals.plus, manualslib.com)
- Disassembling the Frame:
- Pull the end of the frame support bar off the leg and lower it.
- Push the legs together.(manuals.plus)
⚠️ Safety Precautions
- Restraint System:
- Always use the restraint system.
- Never use it with an active child who may be able to climb out of the seat.
- Never leave a child unattended.(manualslib.com, manuals.plus)
- Weight Limit:
- The maximum weight for this product is 25 lbs (11.3 kg).
- If your child weighs less than 25 lbs (11.3 kg) but is really active and appears to be able to climb out of the swing, immediately discontinue use.(manuals.plus)
- Environmental Considerations:
- Always use the swing where there is adequate ventilation.
- To prevent overheating, keep the swing away from heat sources such as radiators, heat registers, direct sunlight, stoves, amplifiers, or other appliances that produce heat.
- Never use extension cords with the AC adapter.
- Never use the swing near water (e.g., bathtub, sink, laundry tub, or wet basement).(manuals.plus)
- AC Adapter Safety:
- If you use this product with the AC adapter, periodically examine the AC adapter for damage to the cord, housing, or other parts that may result in the risk